Associated Products
Rustins Quick Dry Water Based Wood Dye White 1 Litre
Rustins Quick Dry Water Based Wood Dye White is for use on bare wood prior to finishing with any of Rustins wood finishes. A water-based quick drying penetrating stain which does not raise the grain.
I'm sorry, we've sold out
Don't worry, if you enter your email below we'll notify you when it's back in stock!
Rustins Quick Dry Water Based Wood Dye White 1 Litre
Rustins Quick Dry Water Based Wood Dye White is for use on bare wood prior to finishing with any of Rustins wood finishes. A water-based quick drying penetrating stain which does not raise the grain. May be intermixed with the solvent based colour wood dyes to make an infinite variety of natural wood shades. Suitable for interior and exterior use.
Intended Use: For application to all types of new bare wood and for wood that has been stripped. Suitable for interior and exterior use. The dye must be over-coated/sealed
Type: Microfine pigment and dilute aqueous binder.Special Features: Non-fading. Non-bleeding. Quick drying. Note The final colour achieved depends on the original colour of the wood and the type of coating/finish applied over the dye.
Coverage: Up to 12m² per Litre, per coat, depending on the absorbency of the wood.
Size: 1 Litre
Also Available: Rustins Quick Dry Water Based Wood Dye White 250ml and Rustins Quick Dry Water Based Wood Dye White 2.5 Litre
Rustins Quick Dry Water Based Wood Dye White Usage Instructions
Preparation: Wood must be clean, dry and free of wax, previous coatings and contaminants.
Application: Using a rag or brush, apply an even coat and wipe off any excess. Can be diluted with water but do not exceed a 30% dilution. Before use check that the colour is what is required. Do not mix with white spirit or solvent.
Coats: Usually 1 application is sufficient, or 2 for a lighter/whiter shade.Drying Time: Touch dry in 30 minutes under normal conditions.Re-coating Time: 2 hours under normal conditions of temperature and humidity.
Application Temp: Ideally 15-25°C.
Compatibility: Can be used under all Rustins wood finishes, such as Quick Drying Varnish, Polyurethane Varnish, Plastic Coating, Danish Oil, Teak Oil, French Polish/Shellac. Oil based varnishes/oils can cause a slight yellowing of the colour. To avoid this use use Quick Drying Varnish. Dilutable with water. Do not mix with white spirit.
Settlement: STIR WELL AND SHAKE WELL BEFORE USE. Special note: To ensure the correct strength is obtained, it is advisable to stir the contents at the bottom of the container then shake well before use. Before use check that the colour is what is required .
Clean-Up: Equipment can be cleaned with water whist wet. If dried-on, clean brushes with Rustins Brush Restorer.
Barcode - 5015332000739
Weight: 1.19kg
Shelf-life/Storage: Many years if stored in original, tightly closed container in normal conditions. Do not store below 5°C. Protect from Frost.
Hazards: Non-flammable. May be harmful if swallowed. Avoid contact with eyes and skin. Splashes to eyes and skin should be rinsed with plenty of clean water. Keep out of reach of children.
Rustins Quick Dry Water Based Wood Dye White 1 Litre
Rustins Quick Dry Water Based Wood Dye White is for use on bare wood prior to finishing with any of Rustins wood finishes. A water-based quick drying penetrating stain which does not raise the grain. May be intermixed with the solvent based colour wood dyes to make an infinite variety of natural wood shades. Suitable for interior and exterior use.
Intended Use: For application to all types of new bare wood and for wood that has been stripped. Suitable for interior and exterior use. The dye must be over-coated/sealed
Type: Microfine pigment and dilute aqueous binder.Special Features: Non-fading. Non-bleeding. Quick drying. Note The final colour achieved depends on the original colour of the wood and the type of coating/finish applied over the dye.
Coverage: Up to 12m² per Litre, per coat, depending on the absorbency of the wood.
Size: 1 Litre
Also Available: Rustins Quick Dry Water Based Wood Dye White 250ml and Rustins Quick Dry Water Based Wood Dye White 2.5 Litre
Rustins Quick Dry Water Based Wood Dye White Usage Instructions
Preparation: Wood must be clean, dry and free of wax, previous coatings and contaminants.
Application: Using a rag or brush, apply an even coat and wipe off any excess. Can be diluted with water but do not exceed a 30% dilution. Before use check that the colour is what is required. Do not mix with white spirit or solvent.
Coats: Usually 1 application is sufficient, or 2 for a lighter/whiter shade.Drying Time: Touch dry in 30 minutes under normal conditions.Re-coating Time: 2 hours under normal conditions of temperature and humidity.
Application Temp: Ideally 15-25°C.
Compatibility: Can be used under all Rustins wood finishes, such as Quick Drying Varnish, Polyurethane Varnish, Plastic Coating, Danish Oil, Teak Oil, French Polish/Shellac. Oil based varnishes/oils can cause a slight yellowing of the colour. To avoid this use use Quick Drying Varnish. Dilutable with water. Do not mix with white spirit.
Settlement: STIR WELL AND SHAKE WELL BEFORE USE. Special note: To ensure the correct strength is obtained, it is advisable to stir the contents at the bottom of the container then shake well before use. Before use check that the colour is what is required .
Clean-Up: Equipment can be cleaned with water whist wet. If dried-on, clean brushes with Rustins Brush Restorer.
Barcode - 5015332000739
Weight: 1.19kg
Shelf-life/Storage: Many years if stored in original, tightly closed container in normal conditions. Do not store below 5°C. Protect from Frost.
Hazards: Non-flammable. May be harmful if swallowed. Avoid contact with eyes and skin. Splashes to eyes and skin should be rinsed with plenty of clean water. Keep out of reach of children.